Treadmill walking belt slows during use: Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-guage cord of five feet Treadmill walking belt slows during use: Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-guage cord of five feet Find out which type is best suited for your needs. Access the wax test by turning "ON" the FIT TEST. weblink
D) Inspect all drive motor wiring and connections. Start Up Error Check the opto (speed) sensor connection and wires. Then run body mass program again. Inspect all connections at the CPU control board and suppressor board.
Treadmill Error Code E1
Save the settings by pressing now pressing CLEAR twice. 9000, Serial# 344637-344672, 341200-344636, 339500-341199 Notify Maintenance Lift Control Error A) Access the incline manual mode in diagnostics by pressing 9, 1, H) Re-tension the running belt. Start Error A) Inspect cable and connection of opto (speed) sensor. Turn the power off, wait 5 minutes then press the rest switch.
End the test by simply turning the power switch to the OFF position. Inspect wax reservoir and fill if necessary. Negative Switch Error Switch the wire harnesses on the negative and level switches. Horizon Treadmill E1 Error Code Try to slow the belt by applying pressure with your foot against the belt movement while grasping the handrails.
Bulk Order Most Recently Added: more items in your cart. Inspect wiring for damage. If the display now works properly, replace the damaged wiring harness. B) Inspect cable and connection of opto (speed) sensor.
B) Ensure treadmill is connected to a dedicated 120V, 20 Amp circuit. Treadmill Error E6 Notify Maintenance Speed Control Error A) Ensure treadmill is connected to a dedicated 120V, 20 Amp circuit. Using the INCLINE keys, operate the tracking motor. Turn the power off, wait 5 minutes then press the rest switch.
Treadmill Error Code E2
The manual may also tell you whether or not the problem can be fixed by you or needs to be fixed by a professional. 3 Open the treadmill according to the
Check the following: Does the running belt move? 2. Treadmill Error Code E1 No belt movement Motor is not receiving power: Call an authorized service technician Erratic display function Computer memory loss: Turn off and unplug the treadmill for 5 minutes and retry. + Treadmill Error Codes Waxer Unplugged Cycle motor in waxer manual mode in diagnostics and verify 120VAC at the P6 connector on Wax/Lift PCB.
Repair any damage wiring and reset any poor connections if necessary. http://divxdelisi.com/treadmill-error/treadmill-error-e1.html Motor console damaged. Ben Hudspith 14.653 görüntüleme 3:32 Vídeo 0002F: Ajuste do Sensor ERRO E01 - Linha Fitness: Esteira HF1306(EA35A) Rev 00 - Parte 1/1 - Süre: 5:22. If the running belt moves, does E1 appear after 10 seconds? Treadmill Error Code E3
Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. The treadmill did not move after pressing “Start” and shows E1, please check if t here is any part stuck. Reset 3 amp breaker. http://divxdelisi.com/treadmill-error/trimline-treadmill-errors.html If no continuity, replace the wire harness.
If the treadmill still will not operate, please call 888-800-1167 for service. Treadmill Error Code E7 Power switch not activated Power input circuit breaker blown. Notify Maintenance Incline Timeout Error A) Cycle motor in incline manual mode and verify 120VAC at the P7 connector on the Wax/Lift PCB.
Show more unanswered questions Ask a Question 200 characters left Submit Already answered Not a question Bad question Other If this question (or a similar one) is answered twice in this Find the cable that goes between the board under the motor cover and the console. B) Inspect the 3 amp circuit breaker. Treadmill Error Codes Manual Contact your dealer if unit is plugged in, powered on and circuit breaker is depressed.
Notify Maintenance Motor Controller Comm Bad A) Replace Motor Controller. If you require additional assistance please call Technical service at 1.888.800.1167. + return to top 6.75 Troubleshooting E1 Error Code When E1 is displayed, remove safety key and insert it again You can change this preference below. this content Clean wax nozzle if necessary by removing and soaking in hot water.
End the test by simply turning the power switch to the OFF position.) The switch should be open at one position and closed in the other. Clean away any obstruction if necessary. If the TOTAL CAL LED is lit but the CAL/HR LED is out, then with your feet off the running belt and on the side rails, press the SPEED UP key. If the error is still shown, turn the treadmill OFF and unplug from the wall outlet.
Then lift the treadmill frame from the rear end slightly and check if the spring load knob can be locked in. Adjust or replace opto (speed) sensor if necessary. Then press CLEAR key twice. Walk on the unit for 5 minutes.
AC/DC-9 Power OFF and ON. Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If the error code is still shown please contact customer service. If the treadmill still will not operate, please call Technical service at 1.888.800.1167.
B) Inspect alignment of opto (speed) sensor. Notify Maintenance Speed Control Error A) Inspect all cable connections to the motor controller.
© Copyright 2017 divxdelisi.com. All rights reserved.